In stock
Product
2242
SENSOR, OIL PRESSURE, 0-100 PSI, 1/8" NPT MALE, FOR SHORT SWEEP ELEC.
$59.45
Shipping in 2-4 business days
Free Shipping over $99
Hassle Free Returns
Quick Specs
DESCRIPTION:
SENSOR, OIL PRESSURE, 0-100 PSI, 1/8" NPT MALE, FOR SHORT SWEEP ELEC.
A bad oil pressure sensor cannot trigger the warning light when there's low oil or an oil leak. A bad sensor is unable to detect the difference between high oil pressure and low oil pressure. Do not wait for severe damage to your engine. Replace a faulty oil pressure sensor to immediately detect low oil pressure and avoid overheating.
AutoMeter's accurate engine oil pressure reading sends a signal to your oil pressure gauge on the dash to alert you of the problem. Check out Autometer's engine oil pressure sensor feature points below.
Feature Points
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
- Sensor Body Materlal - Plated steel
- Thread size - 1/8 in. NPTF
- Includes 1/4 in. NPT adapter bushing.
- Measures 3.25 in. long from end of threads to tip of sensor stud and 2 in. in diameter.
- Not compatible with fuel.
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
REVIEWS:
Rated 1 out of
5
by
Chris C from
Have had 2 that have failed
My first one worked great for about 4 years. Then it started pegging out over 100psi when running. Key on engine off reads over 60psi. I replaced the sender spring 2019. It worked normally for about a month. Now doing the same, reading way higher than normal even with key on engine off. With key off gauge reads 0. Disconnect sender, key on gauge reads 0. Guess I'll have to order another...
Date published: 2019-07-23
Rated 5 out of
5
by
ARR1950 from
0 TO 100 POUNDS PRESSURE TRANSDUCER
I HAVE USED AUTO METER FOR ALMOST 19 YEARS AND LIKE THEIR PRODUCTS. THERE SHOULD BE A NOTE ON INSTALLATION THT THE SENDING UNIT NEEDS TO BE INSTALLED WITH ELECTRICAL CONNECTION UP SO FLUID CONNECTION IS DOWN. THE HOUSING SEAL TO THE UNIT IS NOT LIQUID TIGHT. SINCE MINE IS UPSIDE DOWN I SEALED THE JOINT WITH A SEALANT SO HOPEFULLY IT WILL NOT ALLOW FLUIDS TO ENTER THE MODULE.
Date published: 2018-01-21
Rated 5 out of
5
by
Jason from
Great parts
Easy install, everything works! Happy I replaced the old ones due to false readings.
Date published: 2018-01-02
QUESTIONS:
Can the 2242 sender be adjusted to calibrate with a mechanical sensor please?
Here are the specs for your 2242:
https://www.autometer.com/sensor_specs
There is no way to calibrate an out of spec sensor, it would have to be replaced.
Date published: 2023-08-15
What size is the nut that holds the wire? Trying to remove and can't quite get a wrench on it?
The nut is officially a 10-32 x 3/8, so 3/8 would be correct.
Date published: 2023-11-15
Any recommended brand of thread sealer? Like a Permatex?
There is no recommendation. However that will work perfectly fine.
Date published: 2023-11-15
Can this be installed with Teflon tape, or will that not allow a ground?
We generally advise against using Teflon tape since the sending unit does need to ground through the threads. You can use a small amount of liquid thread sealer if needed.
Date published: 2024-08-02
i have a 2521 kit no sender what is number for gauge is it 2242
It sounds like you have a gauge that has been obsoleted. Please call 866-248-6357 for assistance.
Date published: 2023-04-03
brought auto gage model 2391 need correct oil pressure sensor # and Temp sensor # to purchase!
https://www.autometer.com/electric-temperature-gauge-sender-autogage-series.html
https://www.autometer.com/100-psi-electric-oil-pressure-sensor.html
The correct senders are in the links above.
Date published: 2022-10-13
will this fit for a 4327 oil pressure gauage?
This 2242 sender is the correct one for the 4327 gauge.
Date published: 2022-07-26
What is the ohm reading on your 2242 oil pressure sender at 0 psi and 100 psi?
The 2242 has 240 ohms at zero psi, and 33 ohms at 100 psi.
Date published: 2023-11-15
You may also like:
Also Purchased With
Check items to add to the cart or
