In stock
Product
2246
SENSOR, PRESSURE, 0-100 PSI, 1/8" NPT MALE
$131.15
Shipping in 2-4 business days
Free Shipping over $99
Hassle Free Returns
Quick Specs
DESCRIPTION:
SENSOR, PRESSURE, 0-100 PSI, 1/8" NPT MALE
Feature Points
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
- Built in connector mates to Delphi Packard Metri-Pack 150 series connector #12065287 (not included)
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
REVIEWS:
Rated 4 out of
5
by
Sc32valve from
Very short life span. Went through 3 in 7 years!
These senders seem very finicky. They don't last long under normal use and even shorter if it's a vehicle that doesn't get driven often (~3000 miles per year). I've gone through 3 sensors in 7 years, that just doesn't seem right.
Date published: 2020-06-16
Rated 1 out of
5
by
87Buick from
Sending unit is inferior.
Sending unit failed within 3000 miles on an E85 87 Buick Grand National. Pegged at 100psi. Went through the troubleshooting process and it determined sending unit was not sending back the proper voltage to gauge. Actual fuel pressure at idle (40psi) was verified to be accurate with a mechanical gauge.
Date published: 2020-08-05
Rated 3 out of
5
by
Roger 1948 from
not a reliable sending unit
this is the fourth sending unit i have purchased through Autometer in the last five years. they either fail or they spring a leak
Date published: 2020-11-24
Rated 2 out of
5
by
GBaron from
Failed after 3 years
A $120 sender unit I expect more than 3 years. Sad.
Date published: 2018-10-23
Rated 1 out of
5
by
Drews from
Sensor failed fast
1000 miles mounted to a turbo Honda motor and the sensor failed. Would not recommend.
Date published: 2023-09-11
QUESTIONS:
Is the 1/8" NPT threaded shank suppose to be tapered? I could not fully thread it into a 1/8" NPT threaded hole. Tried running a tap to clean up the threads on the hole and still doesn't thread in more than 3-4 threads into the hole.
This is common for any NPT thread. The threads eventually will seal causing you to not thread the sender in further.
Date published: 2022-09-09
I am an International customer from Netherlands. You have free shipping within US. What is in it for International customers? Can you give me some discount on the shipping for this product?
AutoMeter is happy to accept international orders. We use UPS exclusively as our preferred shipper and charge a flat rate of $99.95 for international orders ($39.95 to Mexico and Canada). Please note, this does not cover applicable taxes, duties, fees, etc, which may be charged when the product enters your country. These are the responsibility of the purchaser and will not be paid by AutoMeter. If your country does not appear in our menu system, please call us at 815-895-8141 and we can assist you over the phone.
Date published: 2022-04-14
What does the connector look like?
It would be the same connector for all pressure gauge harnesses but you can reference P/N: 5275 as it will show the connector plug.
Date published: 2020-06-10
Hi. What would you recommend putting on the sender threads to help seal them. Thanks
Thank you for your question. You can use any thread sealant or teflon tape you want with this sensor as it does not ground through the threads.
Date published: 2019-10-16
Hello, Do you have a voltage to pressure ratio? I have a programable management for my engine and I have to manually enter the pressure data in relation to the volt it receives from the sensor.
Thank you for your question. Our sensor specs, including the specs for this sensor #2246, can be found here: https://www.autometer.com/sensor_specs
Date published: 2019-08-28
I have a 2000 SC 281 Saleen. The oil pressure sender is bad. I cannot find a replacement. It is a 3 wire with a fuel shutoff with low pressure . Here is the info on the Sender Autometer 4590 0023 23 PSIG S/N 05294942519
Thank you for your question. We do not have anything in our system that uses that component number. I would recommend contacting our support team so they can get more details and help you identify what sensor you have. You can contact them at 866.248.6357 or https://www.autometer.com/contacts
Date published: 2019-08-06
I have an older Spek oil pressure gauge I cant read numbers on sending unit and the back of the oil pressure gauge has a sticker with the flowing numbersMR0208 031511, I need a sending unit for it- it has a triangle shaped connector 3 pin. What # sender?
Thank you for your question. I would recommend contacting our support team so they can help definitively identify the gauge you have and make sure you get the correct sending unit. You can contact them at 866.248.6357 or https://www.autometer.com/contacts
Date published: 2019-07-17
What wiring harness goes between this sending unit and dash gauge?
Thank you for your question. This sensor and appropriate pressure gauge will work with harness #5227.
Date published: 2019-06-13
You may also like:
Also Purchased With
Check items to add to the cart or
