You have no items in your shopping cart.
Replacement sending unit for AutoMeter Marine 0-100 PSI Oil Pressure gauges.
- ADDITIONAL NOTES
- SHIPPED WITH
SENSOR, OIL PRESSURE, 0-100 PSI, 1/8" NPT MALE, FOR SHORT SWEEP ELEC. is rated out of 5 by 2.Rated 5 out of 5 by Manuel from Oil press sensor I bought this to replace the old oil pressure sensor, that was bad on my truck. It was send right the first time with no problems.Date published: 2018-11-05Rated 4 out of 5 by ALDO from Pressure sender What is the Ohmios range of this sender? maybe 240 ohm for 0 PSI and 30 ohm for 100 PSI.Date published: 2018-05-25
would this sender be accurate with an 80 pound stewart warner sweep gaugeThank you for your inquiry. Our senders will not work with Stewart Warner gauges.Date published: 2020-01-27
I'm installing a short sweep oil pressure gauge on a SBC, the sending unit is hitting on the manifold and if i use an adapter it will hit the MSD distributor. Is there a smaller diameter sending unit available?Thank you for your question. Unfortunately we do not have a different sending unit. I would recommend remotely mounting the unit to the fire wall or using an adapter to position the sensor in a different location.Date published: 2020-01-06
I need a oil sending unit that has 2 wires on it .. I have some of your gauges in my boat can you help?Thank you for your question. We do not have any two wire pressure sending units. Our short sweep pressure gauges are compatible with this sensor. Our full sweep pressure gauges would be compatible with our 3 wire sensor #2246.Date published: 2019-07-23
Will this sending unit work with the gauge part number 200744-35 marine oil pressure gauge 0-80 psi?Thank you for your question. This sensor is not compatible with that gauge and it will cause it to read slightly low. That gauge should be used with 240-33ohm 0-80psi sensors such as the VDO 360 801: https://www.vdo-gauges.com/sensors/pressure-sensors-switches/pressure-sender-80-psi-240-33ohm-1-8-27.htmlDate published: 2019-07-09
whats the difference between the 990342 and the 4424 sending units Thank you for your question. I assume you mean 2242 not 4424. There is no difference, they are the exact same thing. 990342 is the part # it is given when referenced for marine applications and #2242 is the part # it is given when it is referenced with automotive applications. That is the only difference.Date published: 2019-06-20
Does this work with atm 4327 gaugeThank you for your question. Yes, this sensor will work with that gauge. This is the marine part # for the 2242 sensor. They are the exact same sensor, one number was created for marine distributors and the other was for automotive distributors. You can purchase either part number and it will work on your gauge.Date published: 2019-05-21
I have AutoMeter gauges in my '71 Camaro for ... years. According to the gauge, the oil pressure may be fluctuating a bit. My question is: will a PS154 sending unit work with the oil pressure gauge? I don't want to break something. Thanks...Thank you for reaching out to us. You will have to use the AutoMeter sender that is compatible the gauge you have. I would recommend reaching out to our Service Team to confirm which gauge you have and which sender will be required. They can also provide some troubleshooting steps to determine if you are having a sender issue. You can call us at 866-248-6356 or email us anytime at https://www.autometer.com/contacts.Date published: 2019-04-27
what is the driff in short sweep and full sweepHi Burnett, thank you so much for contacting us. In simplest terms, an air core, short sweep gauge uses less of the dial to display and is a little more economical. A digital stepper motor, full sweep gauge uses a much larger portion of the dial to display and offers enhanced accuracy, response and durability, both in the gauge and the sender. You can read about it much greater detail in this article: https://www.autometer.com/resources/index/faq_view/id/78 Hope this helps!Date published: 2018-03-28
California Prop 65 Warning