In stock


Shipping in 2-4 business days
Free Shipping over $99
Hassle Free Returns

Quick Specs


Ready to upgrade the instrumentation in your hot rod, but finding the wiring a bit daunting? AutoMeter has you covered with their Universal Gauge Wire Harness. Pre-terminated and color coded with detailed installation instructions, this product provides everything you need to wire a standard 5 or 6 instrument set, including turn signal and high beam LEDs!
Feature Points
  • Accomodates 5 or 6 gauge installations consisting of any AutoMeter In-Dash Tachometer, Speedometer, and four short sweep electric, air-core gauges (Fuel Level, Oil Pressure, Water Temperature, and Voltmeter)
  • Color coded and pre-terminated for simpified installation.
  • Includes: Main Wire Harness (gauge side and vehicle side with pre-terminated multi-pin separation connectors), Lighting Ground Wire Harness, 8 butt connectors, 8 crimp connectors, 2 green turn signal LEDs, 1 amber high beam LED, 1 red brake or check engine LED.
  • Not intended for use with the following AutoMeter gauge types: Digital Stepper Motor, Digital Display, Dual Gauge, Mechanical, Quad Gauge, or Tach/Speedo Combo.
California Residents: Prop 65 WARNING prop65 Cancer, Birth Defects and Reproductive Harm


Rated 5 out of 5 by from Gauges work and look much better than expected. Love these gauges. Definitely order the wiring harness. It made a two day project into a 12 hour day. I would also suggest getting a LabelMaker. Label all your wires before you cut them from your existing harness. I also ordered a Classic Dash to house my new gauges. It’s pretty much plug-and-play. I have a 69 Camaro and had a trim some of my dash pad. I did not use the LED indicator lights that were included with the wiring harness. I ordered much nicer LED indicators from Amazon.
Date published: 2018-01-11
Rated 5 out of 5 by from easy wiring I really didn't need to replace my gauge wiring, but this kit let me eliminate a lot of extra wires under my dash and made it very easy to hook up the gauges plus it gives me just one plug to use if I ever need to remove the instrument panel
Date published: 2022-02-22
Rated 5 out of 5 by from Saves a ton of headache Bought a six guage setup for my car...went to begin installing it and found I would have to make a harness. Went back online and the plug in harness. Wish someone told me when I purchased my guages. Worked great
Date published: 2020-06-15
Rated 5 out of 5 by from Amazing This make it so much easier to install the gauges in the dash
Date published: 2018-12-05
Rated 5 out of 5 by from Gauge set wiring harness A real timesaver, worth the money. Great customer service.
Date published: 2017-12-19
Rated 5 out of 5 by from Worth the money! Worth the money! saves a lot of time. good instructions,
Date published: 2018-08-03
  • y_2024, m_4, d_15, h_3
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.41
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_2198, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_autometer-us
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getReviews, 31.6ms


Does this include the wires to go to the sensors that place on the motor? Such as oil pressure, trans temp, water temp?

Asked by: MoonKnight_YJ
The harness does have color coded wires designated to certain gauges signal input. You can then use those color coded wires to connect to the proper sending unit that applies to said gauge. For further assistance please give us a call at 866-248-6356.
Answered by: Steve from AutoMeter
Date published: 2024-02-29

Hello, will this harness work with the American muscle electric 5piece gauge set.

Asked by: TysToyz
Thank you for your question. This universal harness will work with the American Muscle 5 piece set.
Answered by: Alex at AutoMeter
Date published: 2024-02-26

I have gauge set 3182-1809 what harness can I use thank you

Asked by: da46
Thank you for your question. This is our universal wiring harness which will work with most of our short sweep electric gauge kits including kit number 1809.
Answered by: Alex at AutoMeter
Date published: 2023-12-06

how do you calibrate the speedometer with the invision dash in a 1987 Chevy Monte Carlo?

Asked by: Bandaid
Thank you for your question. The invision speedo calibration is performed with a 2 mile calibration trip. The instructions on how to put the dash in calibration mode can be found on page 5 of the instructions. They can be found at:
Answered by: Alex at AutoMeter
Date published: 2023-11-20

Do you offer a wiring harness compatible to use with auto meter gauge set 1820 Thamks. Ed

Asked by: Young
Ed, Unfortunately we do not. You will need to use P/N: 3299 (qty: 2) to create your own harness if you wanted a connector plug that would work for the gauges.
Answered by: Steve from AutoMeter
Date published: 2023-10-17

I have 4 Phantom II stepper motor gauges, Speedo and Tach. What wiring harness can I use with these?

Asked by: Keith71
Unfortunately we do not sell a wiring harness kit for the phantom series gauges as the majority of those gauges come with their own wiring harnesses.
Answered by: Steve from AutoMeter
Date published: 2022-07-06

Will this plug into a 1996 Mustang 5" Tachometer?

Asked by: Outlaw88
Sorry, but I can't help with this. I used this harness to hook up a 5-gauge setup with a 3 1/8" tach on a Chevy truck. I would think you'd get a quick answer on one of the Ford forums, as this would be an easy one for the blue oval crowd. Of course, if you're going to be rewiring your gauges (at least your tach), you're going to see what type of connector you have on the back of the unit, and you can match it with the right harness.
Answered by: chevyhed53
Date published: 2020-05-27

is this wire 18 or 20 gauge ? terry

Asked by: terry crisman
If I had to guess I'd say 20.
Answered by: Bigblue
Date published: 2020-02-04
  • y_2024, m_4, d_15, h_3CST
  • bvseo_bulk, prod_bvqa, vn_bulk_3.0.41
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_20
  • loc_en_US, sid_2198, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_autometer-us
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 30.96ms