In stock
Product
2277
FITTING, ADAPTER, METRIC, M12X1.5 MALE TO 1/8" NPTF FEMALE, BRASS
$16.66
Shipping in 2-4 business days
Free Shipping over $99
Hassle Free Returns
Quick Specs
- Instructions: Download PDF
DESCRIPTION:
1/8" NPT Female to M12x1.5 Male for electric temperature or pressure Commonly used for electric temperature gauge installation in GM LS engine cylinder heads. If using with a Short Sweep Electric Temperature gauge, sender #2259 is also required.
Feature Points
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
- Constructed from solid brass
Cancer, Birth Defects and Reproductive Harm www.P65Warnings.ca.gov
REVIEWS:
Rated 1 out of
5
by
Bhill4 from
Does not fit
The inside diameter of this fitting is too small to allow the autometer water temp sending unit that came with my C2 gauge to fit inside. I had to drill it out and then re-tap the 1/8 -27 threads. Not sure why autometer would make this part not work with their own gauge sending units. only took 5 mins but still something that shouldn’t have to be done.
Date published: 2019-04-26
Rated 4 out of
5
by
maybe368 from
Only one I could find
If you need to connect an oil pressure gauge to the port where the oil pressure sending unit goes on a Mercedes Benz 300 SDL and others I'm sure, you need this adapter. I bought a generic oil pressure kit that has 8 or 10 adapters, none of them correct. Shipping was slow, put the ad did say up to 5 business days.
Date published: 2018-06-22
QUESTIONS:
What is the maximum torque spec for this?
Thank you so much for contacting us. Our supplier on these bushings does not publish a torque spec, but a good rule of thumb is to get them just snug enough to crush the washer. They do not need to be very tight to seal. It is also worth mentioning, when using one of these for water temp on an LS engine and an AutoMeter Air Core gauge (1 wire sending unit), use the shallow depth sending unit and don't attempt to drill out the adapter. Here's a link to the shallow depth sender: https://www.autometer.com/shallow-depth-electric-temperature-sender-250-300-and-340-deg.html Hope this helps!
Date published: 2023-02-09
Is it appropriate to use Teflon sealing tape on the threads of your 2277 bushing?
Thank you for your question. Yes, you can certainly use thread sealant with our 2277 adapter.
Date published: 2019-05-30
Hi, as the cross section is weak for this part, do you have a torque recommandation to set it in place? Thks
HI Pascal, thank you so much for contacting us. Our supplier on these bushings does not publish a torque spec, but a good rule of thumb is to get them just snug enough to crush the washer. They do not need to be very tight to seal.
It is also worth mentioning, when using one of these for water temp on an LS engine and an AutoMeter Air Core gauge (1 wire sending unit), use the shallow depth sending unit and don't attempt to drill out the adapter. Here's a link to the shallow depth sender:
https://www.autometer.com/shallow-depth-electric-temperature-sender-250-300-and-340-deg.html
Hope this helps!
Date published: 2018-03-20
Is part # 2277 available as an extension adapter? Extra water passage clearance is needed for a temperature sensor. Thank you.
Hi Mike, thank you so much for the question. Sorry, no extended version available. This is the only M12X1.5 adapter we offer.
Date published: 2018-03-19
Is the female M12 and the male NPTF? The threads in the female portion appear smaller than the male end. That is why I’m wondering if description could be opposite by mistake?
i have 2007 sl55amg mercedes. specs say i need 12x1.5 adapter to install an electrical oil pressure gauge. will this work on my model? the gauge im getting has 1/8 inch male threads.
You may also like:
Also Purchased With
Check items to add to the cart or
