You have no items in your shopping cart.
Tickets are no fun. Calibrating a speedometer isn’t a great deal of fun either. AutoMeter’s Electronic Programmable Speedometer makes short work of both, providing an easy to install and easy to calibrate solution that will help keep your speed exactly where it needs to be. Compatible with most factory speed senders, you’ll wonder why you ever struggled with a speedometer before. Calibration is as simple as a two mile drive, or for even easier operation, AutoMeter’s GPS Speedometer Sender is a simple plug and play solution for any application.
- ADDITIONAL NOTES
- Traditional incandescent lighting illuminates around the perimeter of the dial
- Features lit LCD odometer - capable of registering one-million miles with two resettable trip odometers
- Compatible with most two wire sine wave and three wire hall effect vehicle speed sensors.
- Simple push button, 2 mile drive calibration. No dip switches!
- Reprogram at any time to accommodate changes in gear ratio or wheel and tire combination.
- Gauge kit includes bulb and socket assembly, red and green bulb covers, mounting hardware, and detailed instructions for installation
- SHIPPED WITH
Bulb & Socket
- Red 3214 & Green 3215
- Bracket Included
will this work on a 2000 5.3 4000ppm square wave signal, that is the vss signal out of the pcmThank you for your question. The speedometer will calibrate to match your vss during the 2-mile calibration drive.Date published: 2018-10-29
I have a Bugatti Kit car built on a 1969 VW Bug. My question is I have ordered a cable that converts the analog to electronic signal for speedo using Inductive Sensor. Will this speedo work with that setup? Also can I set the original mileage?Thank you for connecting with us. Our electronic speedometers will read a sine-wave type signal or a hall-effect signal. Unfortunately, without know exactly what type of signal your device produces, we can't make any guarantees. But if it's designed to run an electronic speedometer, it should work with ours. There are no adjustments that you will be able to do with mileage, but you can special order with any mileage for a small additional service charge. If you'd like to inquire further about the special order, give us a call at 866-248-6356 or email us here: https://www.autometer.com/contactsDate published: 2018-10-18
Hello Im wanting to install this in a 1952 chevy truck and use the autometer gps interface will this work for my application.Hi John, thank you for the question. Yes, the GPS Interface and any AutoMeter electronic programmable speedometer will be compatible with your truck. 12 volts would be the only requirement. However, our 5" Speedometer fits into a 4-5/8" diameter hole. If you're looking to fit this into the existing hole in your '52 dash, you'll need something like our direct fit insert: https://www.autometer.com/direct-fit-dash-insert-chevy-truck-47-53-2-gauge-billet.htmlDate published: 2018-04-13
I have installed a Rostra universal cruise control. I am using the magnetic VSS generator (driveshaft) signal generator). Can this signal be shared with the speedometer?Hi Dave, thank you for the question. Yes, our speedometer will trigger and operate off your VSS. There is a slight possibility that either our speedometer or your cruise could be affected by that shared "weaker" signal, but no damage would ever come to our speedometer. It would simply drop off speed or not operate.Date published: 2018-05-08
is model 1889 5" speedometer bezel chrome or gold?Hi Dave, thank you so much for contacting us. The 1889 Speedometer has a chrome bezel. We could however do a special order with a gold bezel to match up with the Golden Oldies series if that's the direction you wanted to go. Hope this helps!Date published: 2018-03-28
i need a speedometer that is 5 inches in diameter for the existing hole in my 1937 cadillac dash. the cadillac bezel is designed to protrude through the hole and be larger on the back side. i dont have any area on the face for the bezel to lap overHi Ron, thank you for the question. Our instruments have a larger bezel and smaller case and are designed to mount from the front. The 5" have a 5" bezel O.D. and fit into a 4-5/8" diameter hole.Date published: 2018-03-27
Would you be able to make the antique speedo so that zero is on the lower right and the speedo goes in reverse? This is for a Cobra?Hi Rich, thank you so much for the question. Unfortunately, we would not be able to create a special version, but we do offer a 4" Cobra replica speedometer in both mechanical (model 201005) and electronic (model 201013).Date published: 2018-03-06
I have this cage and recently hooked it up to the computer LS one. It is reading approximately 25% of what it should be reading. I’ve lost the instructions do you have suggest Hi Doug, thank you so much for contacting us. You'll simply need to recalibrate the unit. Easy calibration instructions for AutoMeter speedometers can be found here (both written and video): https://www.autometer.com/resources/index/faq_view/id/35 Hope this helps!Date published: 2018-02-15
California Prop 65 Warning