You have no items in your shopping cart.
For 240 Ohm Empty / 33 Ohm Fuel Gauge models. Adjustable for 5" - 24" deep tank. Fits standard 5-bolt mounting flange.
- ADDITIONAL NOTES
- For 240 Ohm Empty / 33 Ohm Fuel Gauge models.
- Adjustable for 5" - 24" deep tank.
- Fits standard 5-bolt (2.125 in. circle) top mounting flange.
- SHIPPED WITH
- Hardware Included
I have the 2 PC. GAUGE KIT, 3-3/8" QUAD & TACH/SPEEDO, ELECTRIC, 240-33 Ω, ARCTIC WHITE Product # 1309. will this sending unit work with my gauge?Thank you for your question. Yes, this will work with your 240-33Ohm gauge.Date published: 2018-11-05
will this fit a 1993 honda prelude and if not is there an adapter so I don't have to modify this?Can not answer your question directly. However, I found it fairly easily to remove the white plastic rheostat, take it apart, swap the float holder to the opposite side (has a spring and 2 caps inside, so disassemble it carefully) and mount it on an fuel pump assembly. I installed a '97 Mercury Mountaineer fuel tank under the bed of my '72 Ford pickup and using all AutoMeter gauges.Date published: 2018-10-24
Is just the float arm assembly available for the #3262 fuel level sending?Thank you for connecting with us. The float arm is not available as a standard, sell-able part, but if you are in need of one, I would recommend reaching out to our Service Team at 866-248-6357 or via email through the following link: https://www.autometer.com/contactsDate published: 2018-08-14
this is just over 3 years old, has been sitting in the shop after I had a stroke. This has rusted up on me. Since this is over the 12 month warranty period, is there something I can do to get this working again or should I just trash is and buy another ?Thank you for reaching out to us. I would recommend contacting our Service Team by phone at 866-248-6357, by chat via the link at the top of the page, or via email through the following form. https://www.autometer.com/contacts They may be able to provide some assistance for you on your sender.Date published: 2018-07-16
Are there any issues using this with diesel or biodiesel?Hi Johnny, thank you for the question. The 3262 is compatible with gasoline, ethanol, E85, E10, methanol, diesel #1, and diesel #2, but unfortunately, no specification for biodiesel at this time.Date published: 2018-06-19
How do I set the fuel guage to read my sending unit,my guage has two buttons on it,my sending float is 240 full and 33 emptyHi Stan, thank you so much for contacting us. It totally depends on the gauge you have. Without knowing the exact gauge you've got, it would be tough to say for certain. Guessing based on the limited information I've got, I'd suggest maybe looking at this instruction: https://www.autometer.com/media/manual/2650-1443.pdf With that said, it very well could be another unit. It may be best to look at your gauge and give our tech team a call at 866.248.6357. Hope this helps!Date published: 2018-03-20
what gauge cat# do I use with this ?Hi Doug, thank you so much for contacting us. You'll want to pair this sender with any of our 240 ohm empty, 33 ohm full fuel level gauges. Here's a link to check out: https://www.autometer.com/catalogsearch/result/?q=fuel+240#1&profile=products Hope this helps!Date published: 2018-01-30
will this sending unit be a direct fit on a 1955 chevy 210 sedan gas tank ?Hi Doug, thank you so much for contacting us. This sending unit is adjustable, and therefore will work with most tank setups that utilize a 5 bolt mounting flange. We also have a 6 bolt adapter available for applications that utilize that flange. I wouldn't call it a direct fit as it isn't designed specifically for one vehicle. Depending on the configuration of your fuel pickup, that may need to be accounted for in the installation as well. Hope this helps!Date published: 2018-01-30
working on a John Deere 675B. I applied resistance in 10 ohm increments in line to ground. At 40 ohms produces a full mark gage reading, 90 ohms full side of 1/2, 100 ohms empty side of 1/2. Extrapolation: 150 empty - 40 full. Will this sendor work?Thank you for contacting us. If your gauge is designed to read a 150-40 ohm sender, we don't feel you would get very good results with this sender. You will have inaccurate results from full to half, but more importantly, potentially 1/4 to 1/2 left in the tank with the gauge reading empty.Date published: 2017-12-18
I have a customer that has a fuel cell and he wants me to install a guage, is there a sender that can be used with a fuel cell?Hi Nelson, thank you so much for contacting us. This is the one and only fuel level sender that we offer, but we have definitely used them with fuel cells before. If you've got a foam lined cell, you'll want to look into the shaft style senders which are available typically through the fuel cell manufacturer. We offer a number of different resistance ranges in our fuel level gauges that ill match up with every common fuel sender range. Hope this helps!Date published: 2018-03-06
California Prop 65 Warning